Iranian Journal of Materials Science and Engineering

---

This study was launched to investigate the effects of heating rate and aging parameters on the kinetic of precipitation reactions in a high alloy high strength steel having Ni, Co, Mo and Ti. For this purpose, as quenched specimens were subjected to three types of aging methods with different heating rates. These methods consisted of aging in Pb bath, salt bath, and furnace at different aging cycles. The kinetic of precipitation in each method was studied by hardness measurements and was described adequately by the Johnson-mehl-Avrami equation. Remarkable increase in hardness and its rate is observed when the rate of heating increases. The substantial increase in hardness of the specimens aged rapidly in salt & Pb baths, compared with those aged normally in furnace, seemed to be due to the formation of thermo elastic stresses during sudden expansion of the substance subjected to rapid heating. According to the results obtained in this research, increase in the Avrami constants, n & k, and decrease in the start time of transformation, ts, are associated with heating rate increasing. Analysis of the observed and calculated data for hardness using Arrhenius equation, shows that for the same amount of volume fraction of precipitates, the activation energy of precipitates decreased for f=25 and 50%, while at f=90 % it increased by increasing heating rate.

---

Fracture behavior of a 7075 aluminium alloy reinforced with 15 Vol%. SiC particles was studied after T6 and annealing heat treatments under uniaxial tensile loading at room temperature. The scanning electron microscopy of fractured surfaces and EDS analysis showed:, that fracture mechanism changed from due mainly to fractured particle in T6 condition to interface decohesion in samples in annealed state. Different fracture mechanisms in annealed and T6 conditions can be ascribed mainly to the significant difference in the stress concentration levels around the particles. In T6 condition, very high local stress sufficient to cause fracture of particle can be generated during loading, while the presence of large precipitates at the particle/matrix interface produced interface decohesion leading to final fracture in the annealed state.

---

In this research pitting Corrosion of a sensitized 316 stainless steel was investigated employing potentiodynamic, potentiostatic techniques. Sensitization process was carried out on as-received alloy by submitting the specimen in electric furnace set at 650°Cfor five hours and then the specimen was quenched 25°C water. Potentiodynamic polarization of as received and sensitized specimens in 1M H2SO4 solution at room temperature and 70°C clearly revealed that the sensitization process has caused a magnificent change on electrochemical behavior of the specimen by changing critical current density for passivation, passivation potential and passive current density. Optical microscopy examination of the specimen surface after oxalic acid electrochemical etching also showed the deterioration of grain boundary of sensitized specimen due to chromium carbide precipitation in compared to as-received one. Several anodic potentiodynamic polarization on rode shaped working electrodes prepared from as-received and sensitized specimen in 3.5% NaCl test solution proved an average ~220 mV drop in pitting potential due to sensitization. Anodic potentiostatic polarization at 400 and 200 mV above corrosion potential also demonstrate the deterioration of pitting resistance of alloy as a result of sensitization. Scanning electron microscopy examination of anodically polarized of sensitized specimen at 700mVprior and after oxalic acid etching revealed large stable pits with lacy cover and also openpits with deep crevice for etched specimens.

---

In wire arc spraying, the atomizing air pressure and applied nozzle system are important factors influencing particles characteristics and coating quality. The aim of this paper is to study how the characteristics of particles such as size, velocity and temperature are influenced by the operating conditions in wire arc spray. For that, three types of wires are tested: solid wire of stainless steel 316L, cored wires 97MXC and 98MXC. Arc spray gun is an Arc Jet 9000 manufactured by TAFA. For each condition, the particles temperature and particles velocity are measured using an imaging CCD camera, Spray Watch (Oseir Ltd). Particles size distributions are determined with a laser grain meter. The morphology and composition of particles were evaluated with SEM, EDX and X-Ray diffraction. Results induce important modifications in the particles size distributions and particles velocity. A small diameter nozzle and high atomizing air pressure resulted in a reduction in particles size distributions and an increase in particles velocity.

---

Abstract: Static recrystallization (SRX) behavior of a composite based 7075 Aluminum alloy reinforced with SiC particles was studied during annealing the deformed samples at high temperatures. The results showed an absence of SRX in the samples annealed after hot working at the same deformation temperature, however, a rise in annealing temperature of 100-1500 􀁱C above that the deformation temperature led to full recrystallization. This can be ascribed to the relatively moderate dynamic recovery and the presence of dispersions which stabilize the substructure. Particle stimulated nucleation (PSN) had a significant effect on the grain size in deformed samples at low temperature, but no PSN was observed in samples strained at high temperatures. The possible cause might be that at high temperature the dislocations can be annihilated by climb process around the particles together with the absence of deformation zone for nucleating the recrystallization.

---

Abstract: Problems such as the difficulty of the selection of processing parameters and the large quantity of experimental work exist in the morphological evolutions of Semisolid Metal (SSM) processing. In order to deal with these existing problems, and to identify the effect of the processing parameters, (i.e. shearing rate-time-temperature) combinations on particle size and shape factor, based on experimental investigation, the Artificial Neural Network (ANN) was applied to predict particle size and shape factor SSM processed Aluminum A.356.0 alloy. The results clearly demonstrated that, the ANN with 2 hidden layers and topology (4, 2) can predict the shape factor and the particle size with high accuracy of 94%.The sensivity analysis also revealed that shear rate and solid fraction had the largest effect on shape factor and particle size, respectively. The shear rate had a reverse effect on particle size.

---

Abstract: The objective of this research was to develop a tungsten heavy alloy (WHA) having a microstructure and properties good enough to penetrate hard rolled steels as deep as possible. In addition this alloy should not have environmental problems as depleted uranium (DU) materials. For this purpose a wide spread literature survey was performed and on the base of information obtained in this survey, three compositions of WHA were chosen for investigation in this research. The alloys namely 90W-7Ni-3Fe, 90W-9Ni-Mn and 90W-8Ni-2Mn were selected and after producing these alloys through powder metallurgy technique, their thermal conductivity, compression flow properties and microstructures were studied. The results of these investigations indicated that W-Ni-Mn alloys had better flow properties and lower thermal conductivities relative to W-Ni-Fe alloy. In addition Mn helped to obtain a finer microstructure in WHA. Worth mentioning that a finer microstructure as well as lower thermal conductivity in this type of alloys increased the penetration depth due to formation of adiabatic shear bands (ASB) during impact.

---

Abstract: In chloride salt solutions, titanium alloys exhibit reasonably high pitting potentials as high as +10 V (vs. Ag/AgCl) at room temperatures. On the other hand, anodic pitting potentials are significantly lower in bromide solutions. In this study, pitting corrosion of commercially pure titanium in aqueous NaBr solution of 0.1 M concentration at room temperature was studied and the effect of an external magnetic field oriented both parallel and perpendicular to electrode surface was investigated. Cyclic potentiodynamic and potentiostatic polarization tests were carried out. Anodic breakdown potential of +1.45 V (vs. Ag/AgCl) obtained in the absence of magnetic field, decreasing to +1.11 V in the presence of a 0.05 T parallel magnetic field. The perpendicular magnetic field actually did not affect the breakdown potential. Applying of an external magnetic field, independent of its orientation, shifted the repassivation potential approximately 150 mV in the positive direction. SEM microscopy observations of sample surfaces indicated that applying of magnetic field results in some variations in the pit shapes and their sizes.

---

Abstract: In this paper solid state reduction of high carbon ferrochromium-chromite composite pellets in the temperature range of 900-1350°C was investigated. A two stage reduction mechanism is proposed. The first stage is likely to be controlled by the chemical reaction with activation energy of 127.2kJ/mol. In the second stage, solid state diffusion of carbon through the reaction product layer is suggested to be rate controlling. The activation energy of this stage was calculated to be 93.1kJ/mol. The reduction process was found to be favored by high temperatures as well as high vacuum. The results also show that pre-milling of initial mixture has a negative effect on the reduction degree.

---

Abstract: To ensure the rail transportations safety, evaluation of fatigue behavior of the rail steel is necessary. High cycle fatigue behaviour of a rail steel was the subject of investigation in this research using fracture mechanics. Finite element method (FEM) was used for analyzing the distribution of the stresses on the rail, exerted by the external load. FEM analysis showed that the maximum longitudinal stresses occurred on the railhead. To find out about the relation of crack growth with its critical size, and to estimate its lifetime, the behaviour of transverse cracks to rail direction was studied using damage tolerance concept. It revealed that transverse crack growth initially occurred slowly, but it accelerated once the crack size became larger. Residual service life was calculated for defective segments of the rails. In addition, allowable crack size for different non-destructive testing intervals was determined the allowable crack size decreased as the NDT intervals increased.

---

Abstract: Thermal fatigue is a stochastic process often showing considerable scatter even in controlled environments. Due to complexity of thermal fatigue, there is no a complete analytical solution for predicting the effect of this property on the life of various components, subjected to severe thermal fluctuations. Among these components, one can mention car cylinder, cylinder head and piston which bear damages due to thermal fatigue. All these components are usually produced by casting techniques. In order to comprehend and compare the thermal fatigue resistance of cast Al alloys 356 and 413, this research was designed and performed. For this purpose, several samples in the form of disc were cast from the two alloys in sand mould. The microstructures of the cast samples were studied by light microscopy in order to choose the samples with the least amounts of defects for thermal fatigue tests. The results of thermal fatigue tests showed that the nucleation of microcracks in Al-356 alloy occurred at shorter time relative to those occurred in Al- 413 alloy under the same test conditions. In addition, the density of micro-cracks in Al-356 alloy was more than that of Al-413 alloy. The results of fractography on 356 alloy indicated that the cracks were generally nucleated from inter-dendritic shrinkage porosities and occasionally from the interface of silicon particles with the matrix. The growth of these micro cracks was along the dendrite arms. Fractography of 413 alloy fracture surfaces showed that nucleation of microcracks was often associated with silicon particles.

---

Abstract: Austenitic stainless steels exhibit a low hardness and weak tribological properties. The wear behaviour of austenitic stainless steel AISI 316 was evaluated through the pin on disc tribological method. For investigating the effect of wear on the changes in microstructure and resistance to wear, optical microscopy and scanning electron microscope were used. The hardness of the worn surfaces was measured with a micro-hardness tester. Worn surfaces were analyzed through X-ray diffraction. Results showed that with increasing the sliding distance and applied load, the austenite phase partially transformed to ά martensite, and there was no trace of ε phase detected. Due to the formation of probably hard and strong martensite phase, as the sliding distance and applied load increased, the hardness and the wear resistance of the material was increased. Wear mechanism was on the base of delamination and abrasion.

---

Abstract: The possibility of vanadium carbide coating formation on AISI L2 steel was studied in molten salt bath containing 33 wt% NaCl- 67 wt% CaCl2. In this research, the effects of time, temperature and bath composition on growing layer thickness were studied. The vanadium carbide coating treatment was performed in the NaCl-CaCl2 bath at 1173, 1273 and 1373 K temperatures for 3, 6, 9 hours and in bath containing 5, 10, 15, 25 wt% ferrovanadium. The presence of VC formed on the surface of the steel substrate was confirmed by optical microscopy, scanning electron microscopy (SEM) and X-ray diffraction analysis. The layer thickness of vanadium carbide and surface hardness ranged between 4.8 to 25.7 µm and 2645 to 3600 HV, respectively. The kinetics of layer growth was analyzed by measuring the depth of vanadium carbide layer as a function of time and temperature. The mean activation energy for the process is estimated to be 133 kJ/ mol.

---

Abstract:A combination of mechanical activation and Differential Thermal Analysis (DTA) together with X-Ray Diffraction (XRD), and various microstractural characterization techniques were used to evaluate the starting reaction in the combustion synthesis of TiC-Al2O3 composite in TiO2-Al-C system. The mechanical activation was performed on the mixtures of two components of TiO2/Al, Al/C and TiO2/C and then the third component was added according to the stoichiometric reaction for 3TiC+2Al2O3 composite formation. The powder mixtures were heated up to 1450 °C under Argon atmosphere at a heating rate of 10 °C/min. The combustion synthesis temperature was observed to decrease from 962 °C to 649 °C after milling of TiO2/Al mixture for 16 hr. On the contrary, the mechanical activation of Al/C and TiO2/C mixtures for 16 hr made the reaction temperature increase to 995 °C and 1024 °C, respectively. The decrease in reaction temperature as a result of milling the TiO2/Al mixture could be due to an increase of TiO2 and Al interface area as confirmed by TEM micrographs and XRD patterns of milled powder mixture. In addition, DTA experiments showed that for the sample in which TiO2 and Al were mechanically activated the reaction occurred at the temperature even lower than that of Al melting point.

---

Abstract: Nanoparticles exhibit a high reactivity and strong tendency towards agglomeration. In this study, aluminum oxide (alumina) nanoparticles were characterized by gas adsorption (BET), transmition electron microscopy (TEM) and photon correlation spectroscopy (PCS) techniques to assess the agglomeration of the particles. There is a good correlation between the BET and TEM measurements but PCS was larger in the mean and median size and with a degree of agglomerates being detected. Some agglomeration was evident, but most of the particles existed as discrete objects as observed in the (HR) TEM images which were in good agreement with the agglomeration factor.

---

Abstract: Nano- size alumina particles have been synthesized by mechanical activation of a dry powder mixture of AlCl3 and CaO. Mechanical milling of the above raw materials with the conditions adopted in this study resulted in the formation of a mixture consisting of crystalline CaO and amorphous aluminum chlorides phases. There was no sign of chemical reaction occurring during milling stage as evidenced by x-ray diffraction studies. Subsequent heat treatment of the milled powder at 350ºC resulted in the occurrence of displacement reaction and the formation of Al2O3 particles within a water soluble CaCl2 matrix. The effect of higher temperature calcinations on the phase development in this powder mixture was followed by X-ray diffraction (XRD) analysis and scanning electron microscope ( SEM). Differential thermal analysis (DTA) was used to compare the thermal behavior between the milled and unmilled powders. Perhaps the most important result in this study was the observation of á-Al2O3 phase at a very low temperature of 500ºC.

---

Abstract:In this study, an effort has been made to determine the influence of rotational speed of tool on themicrostructure and hardness values of friction stir welded 2024-T851 aluminum alloy. The microstructure of stir zonein the joints has been investigated. It was found that the particles such as Al6(CuFeMn) particles are broken up duringfriction stir welding, and the degree of break up of these particles in the stir zone increases with increasing rotationalspeed. Since the break up of these particles and the recrystallization of new grains happen simultaneously, the brokenparticles would be placed in the grain boundaries. Moreover, the hardness value in the stir zone increases withincreasing rotational speed

---

Abstract: Equal channel angular extrusion (ECAE) is a promising technique for production of ultra fine-grain (UFG) materials of few hundred nanometers size. In this research, the grain refinement of aluminium strip is accelerated by sandwiching it between two copper strips and then subjecting the three strips to ECAE process simultaneously. The loosely packed copper-aluminium-copper laminated billet was passed through ECAE die up to 8 passes using the B_c route. Then, tensile properties and some microstructural characteristics of the aluminium layer were evaluated. The scanning and transmission electron microscopes, and X-ray diffraction were used to characterize the microstructure. The results show that the yield stress of middle layer (Al) is increased significantly by about four times after application of ECAE throughout the four consecutive passes and then it is slightly decreased when more ECAE passes are applied. An ultra fine grain within the range of 500 to 600 nm was obtained in the Al layer by increasing the thickness of the copper layers. It was observed that the reduction of grain size in the aluminium layer is nearly 55% more than that of a ECA-extruded single layer aluminium billet, i.e. extruding a single aluminium strip or a billet without any clad for the same amount of deformation. This behaviour was attributed to the higher rates of dislocations interaction and cell formation and texture development during the ECAE of the laminated composite compared to those of a single billet

---

  Abstract

  The effect of mechanical activation using an attrition mill on the particle size of an ilmenite concentrate and its effect on the ability of the concentrate for Iron separation during hydrochloric acid leaching and the kinetics of the dissolution process have been investigated. It was observed that mechanical activation in an attritor significantly enhances the dissolution of iron in hydrochloric acid while have a slight effect on dissolution of titanium. With the mechanically activated ilmenite using an attrition mill, leaching conversion at 90 ^oC reached to 80%. The kinetic data of leaching of mechanically activated ilmenite was found to follow shrinking core model. Mechanically activating ilmenite using the attrition mill was found to cause the activation energy of leaching to be decrease from 43.69 , found for samples leached without mechanically activated, to 18.23 .

---

  Abstract

  Recovery and recrystallization phenomena and effects of microalloying elements on these phenomena are of great importance in designing thermomechanical processes of microalloyed steels. Thus, understanding and modeling of microstructure evolution during hot deformation leads to optimize the processing conditions and to improve the product properties.

  In this study, finite element method was utilized to simulate thermomechanical parameters during hot deformation processes. FEM results then were integrated with physically based state variable models of static recovery and recrystallization combined with a realistic microstructural geometry. The thermodynamic software Thermo-calc was also used to predict present microalloying elements at equilibrium conditions.

The model performance was validated using stress relaxation tests. Parametric studies were carried out to evaluate the effects of deformation process parameters on the microstructure development following hot deformation of the API-X70 steel